Goodsjack Custom Hydraulic Press Solution Servo Hydraulic Press Machine Manufacturer

The length of the pressing time of the  hydraulic press  should be determined according to the specific workpiece material, specification, thickness, shape, use environment and requirements. When using a hydraulic press for cold processing, bending, stretching, pressing, etc., if the pressing time is too short, it may cause insufficient processing of the workpiece, substandard quality, or even damage to the workpiece or failure of the  hydraulic machine . If the pressing time is too long, it may It causes problems such as energy waste, low processing efficiency, and shortened equipment life.                                                                                 Therefore, when using a  hydraulic press  for pressing, it should be adjusted according to the actual situation. Generally speaking, the pressing time should be set within the range of the process specification and equipment specification. At the same time, it is also necessary to adjust according to the specific condit

Fuel cell stack assembly hydraulic press  is a special equipment manufactured by CNMM specially designed for hydrogen fuel cell stack assembly. Combined with the hydrogen fuel cell installation process, it uses specially designed tooling. After the body rotates, it relies on gravity to automatically position the bipolar plate and Membrane electrodes are easy to install and save time for lamination alignment. It adopts a three-beam and four-column structure, precision linear bearings, actuators and rotary actuators are servo electric cylinders, which can precisely control the force and displacement of press-fitting, and fine-tune the angle of rotation.                                                                                                           The assembly quality of the fuel cell stack has a very important influence on the performance of the battery. The stack assembly process will affect the internal resistance of the stack and the uneven distribution of fuel due to stres

Deep Drawing Press  is suitable Deep Drawing Materials Forming Not only general materials made of metal, copper, and aluminum but also materials made of stainless steel, pure titanium, Inconel, etc. are supported, which fulfill the following needs:                                                   Products previously made by welding two parts together can be manufactured as one piece using a press. Products that were conventionally manufactured by machining can be VA with a press. The sizes we are capable of handling vary depending on the material. We have deep drawing press with press capacities ranging from 10 ton to 5000 ton. In addition, it is also possible for us to deep draw up to 100 μｍ. We support everything from prototyping to  hydraulic press machine  production and can provide services beginning from mold designing. Goodsjack  Deep Drawing Hydraulic Press  Machine, With 25 years extensive experience in stamping industry, Goodsjack has developed a specially designed high-spee

With the rapid development of new energy vehicles, the automotive industry's demand for battery performance is also increasing. Intense market competition has made new energy vehicle manufacturers have higher requirements on the performance of vehicle batteries to ensure the battery life and service life of the vehicle. This demand is a good opportunity for Delishi/Goodsjack, because Delishi/Goodsjack can provide users with higher quality and higher precision new energy battery hydraulic forming processing equipment to meet the increasing demand of the new energy automobile industry.                                                                                   Delishi/Goodsjack  frame guide hydraulic press  has a long history of application in the field of new energy vehicle batteries. It is not only widely welcomed by high-end auto parts manufacturers in China, but also exported to important automobile manufacturing markets such as the United States, Europe, and South Korea. T

C frame hyraulic press  is one of hot selling hydraulic press machine in Delishi/Goodsjack Machinery. Following we will introduce application of servo  C frame Hydraulic Press . 1. Automobile industry: press-fitting of engine components (cylinder head, cylinder liner, oil seal, etc.), press-fitting of steering gear components (gears, pin shafts, etc.), press-fitting of drive shaft components, press-fitting of gearbox components, press-fitting of brake disc components wait. 2. Motor industry: motors, motors, bearings, water pumps, rotors, stators, press-fitting of micro-motor components (spindle, housing, etc.), press-fitting of motor components (bearings, spindles, etc.). 3. Electronic industry: computer, communication, electronics, circuit board assembly (plug-in, etc.), electronic parts press assembly. 4. Household appliance industry: press-fitting of home appliance accessories, riveting of home appliance accessories, etc. 5. Machinery industry: press-fitting of mechanical parts, aut

Four column hydraulic press  is a kind of mechanical equipment that uses the static pressure of hydraulic oil delivered by the oil pump to process metal, plastic, rubber, wood, powder and other products. It is often used in pressing process and pressing forming process, such as: forging, stamping, cold extrusion, straightening, bending, flanging, sheet drawing, powder metallurgy, pressing and so on. Its principle is to use the mechanical transmission of liquid pressure made by Pascal's law. System introduction The four-column hydraulic press is composed of a main cylinder, an upper beam, four columns, a movable beam, an ejector cylinder, a workbench, a hydraulic transmission system and an electric control system. The electronic control system is generally operated by switch buttons, the pressure gauge displays the pressure, and the PLC is the control core. The frequency converter is used to drive the motor to drive the oil pump, and the oil pump provides high-pressure working fluid

The function, performance requirements and installation method of the cooler in the hydraulic press, generally speaking, a oil cooler should be installed in the hydraulic system of the hydraulic press machine. Because the oil cooler plays a vital role in the  hydraulic press machine .                                                                           1. There must be enough heat dissipation area to keep the oil temperature within the allowable range. 2. The pressure loss is small when the oil passes through. 3. When the system load changes, it is easy to control the oil to maintain a constant temperature. 4. Have sufficient strength. Oil cooler installation method: The cooler is generally installed in the oil return pipeline or low-pressure pipeline, and can also be installed in the oil outlet of the hydraulic pump if necessary to form an independent cooling circuit. 1. The cooler is installed at the overflow port of the main overflow valve.  The characteristics of this installa

Diamond vs Hydraulic Press Machine -  Hydraulic Press Solution Manufacturer From the  (SZX)Shenzhen Bao'an International Airport  and  (CAN)Guangzhou Baiyun International Airport  to our factory 1.5 hour's driving. Warmly welcome to visit us at any time. Delishi Machinery Technology CO.,LTD. Goodsjack Hydraulic Machinery Co.,Ltd. Tel: +86-769-83061993  83223615 Fax: +86-769-83231691 Address:  No3 Jinfu Road, Jinma Industrial Park, Liaobu, Dongguan City, GuanDong Province, China E-mail:  info@goodsjack.com ,  sales@goodsjack.com ,  info@dgdelishi.com Skype: alice.goodsjack WhatsApp/Wechat: +86-13642957273 WhatsApp/Wechat: +86-13509801050 Web:  https://www.hydraulic-machine.com   https://www.kccnc.com Web:  https://www.goodsjack.com

Hydraulic Press for Fiber Thermoforming  is a hot press that integrates heating, pressure maintaining, pressure replenishment, vacuuming, and vacuum breaking. The whole hydraulic press machine adopts servo closed-loop control system, which has the advantages of energy saving and low noise. Vacuum hot press is mainly suitable for pressing new materials by vacuuming, such as carbon fiber mobile phone shells, glass fiber flat shells, graphene materials, etc. It is mainly used for automotive interior and structural parts, mobile phones Exterior parts, laptop exterior parts, bicycles, tennis rackets, badminton rackets and other high-end applications. Hydraulic Press for Fiber Thermoforming  has high precision, adopts servo system control, stable pressure, high efficiency, high yield, flexible pressurization, fast vacuum, slow multi-stage pressurization, and multi-stage heating. It is suitable for composite materials, carbon fiber, glass fiber and other products. Compression molding. The hea