How to Improve Work Efficiency Of Hydraulic Press Machine

-

As China leading hydraulic press machine solution, we all hope that we can improve our work efficiency of hydraulic press machine. As an employee, this will not only reduce our workload, but also be appreciated by our leaders, which is simply killing two birds with one stone. But wanting to improve work efficiency is not so simple. Remember the following!

hydraulic press machine

1. The operator of the hydraulic press must be familiar with the principle of the hydraulic system, familiar with the function of the main hydraulic components of the equipment, and master the operating sequence of the system.
2. Before starting the equipment, check whether all the motion mechanisms and solenoid valves are in the original state, and check the oil level in the fuel tank. If an abnormality or insufficient oil is found, it is forbidden to start the hydraulic pump motor and seek maintenance by maintenance personnel.
3. The operator should always check the working condition of the hydraulic system, observe the working pressure and speed, check the size of the workpiece and the wear of the props, to ensure the stable and reliable operation of the hydraulic system.
4. In winter, when the oil temperature of the fuel tank does not reach 25°C, the actuators cannot start to work in sequence, but can only start the hydraulic pump motor to make the hydraulic pump run dry. During summer work, when the oil temperature in the fuel tank is higher than 60℃, pay attention to observe the working condition of the hydraulic system and notify the maintenance personnel to deal with it.
5. The operator cannot damage the interlocking device of the electrical system, cannot push the electric control valve by hand, cannot damage or move the position of each operating gear arbitrarily.
6. For hydraulic equipment that has been shut down for more than 4 hours, before starting to work, the hydraulic pump motor should be started for 5-10 minutes before it can work under pressure.
7. When the hydraulic system breaks down, the operator should not move without permission and should immediately report to the maintenance department.

8. The hydraulic press machine should always be kept clean to prevent dust, cutting fluid, cutting, cotton yarn and other debris from entering the oil tank.

If you need hydraulic press machine,want to improve your work efficiency of hydraulic press machine,welcome to contact GoodsJack.


GOODSJACK HYDRAULIC MACHINERY CO.,LTD

DELISHI  MACHINERY TECHNOLOGY CO.,LTD

Hydraulic Press Machine, Hydraulic Forging Press Manufacturer

Web: https://www.kccnc.com
         https://www.goodsjack.com

Dongguan Factory
General Factory : No3, Jinfu Road, Jinma Industrial Park, Liaobu Town, Dongguan, Guangdong, China
Branch Factory: No210 Heshi Road, Qiaotou Town, Dongguan, Guangdong, China
Hubei Factory
Address: Sanhua Industrial Park, Binjiang New Area, Huangshi, Hubei, China


Eva Lee   Sales Manager
Email: sales@goodsjack.com
WhatsApp/Wechat:+ 86 13509801050


Alice  Xu    Sales Manager
Skype: alice.goodsjack 
Email: sales1@goodsjack.com
WhatsApp/Wechat: +86 13642957273

评论

发表评论

此博客中的热门博文

Hydraulic Press Machine Speed Slow How To Solve

-
图片
  If your  hydraulic press machine  speed gets slowly,following are methods to solve it. 1. Air in the hydraulic cylinder When the hydraulic press machine pressing speed gets slowly, we should first consider that air in the hydraulic cylinder, interrupt the corresponding exhaust operation through the exhaust equipment of the machine, and check whether there is air in the movement direction of the piston rod. If so, it may be If the sealing ring is defective, the sealing ring should be changed in time. 2.  Check whether the hydraulic pump is operating normally When the hydraulic press machine moves slowly and the hydraulic pump runs irregularly, and sometimes it may be blocked or slightly seized, it means that there is a problem with the hydraulic pump and the hydraulic pump should be repaired or changed in time. 3. Check the operation of the piston When the hydraulic cylinder of a hydraulic press machine with a buffer device is intermittently started in reverse, the piston will be temp
阅读全文

Benefits of Hydraulic Press for AI Servers Forming

-
图片
Hydraulic press offers several benefits when it comes to manufacturing components for AI servers forming: AI server forming ○ Precision and Consistency Hydraulic press allows for precise and consistent shaping of metal components used in AI servers. This is essential for ensuring that the parts fit together correctly and function optimally within the server system. ○ Complex Shapes Hydraulic press enables the creation of complex and intricate metal parts that may be required in the construction of AI servers. This is particularly important as servers often contain components with non-standard shapes to accommodate various functionalities and space constraints. ○ Material Strength The process of hydraulic press can enhance the strength and durability of metal components used in AI servers. This is crucial for ensuring the reliability and longevity of the server hardware, especially in high-demand computing environments.
阅读全文

GOODSJACK supply 3 kinds of hydraulic deep drawing press machine

-
图片
Hydraulic deep drawing press machine is suitable for metal stamping forming products,such as deep drawing and forming of tableware,kitchenware,metal cover of electric motor,household appliances and lighting ware etc. We can supply following three type  hydraulic deep drawing press machine : 1.Normal hydraulic deep drawing press (the cheapest machine) 2.CNC hydraulic deep drawing press(operation more convenient) 3.Hydraulic deep drawing press machine with servo seystem(most efficient and most convenient） We suggest you to choose our  hydraulic press machine  with servo system, because GOODSJACK Machine with servo system, can bring you 7 kinds Advantages as below: 1.Can save 40% - 70% electricity energy. 2.Automatic alarm and auto troubleshooting system, ensure safety and easy to know error. 3.Parameters can be adjusted on the touch screen, easy to operate. 4.Have memory function,if use the original mold, do not need to adjust parameter again, very convenient to change mold, sa
阅读全文